Three-Phase Cyclone Oil Removal Mechanism in Tank-within-Tank Units - Brator
In petroleum refining and petrochemical projects, oily wastewater has always posed two problems at once: staying inside the discharge limit, and recovering the resource the water still carries. Conventional sedimentation tanks rely on gravity, and gravity is a poor tool when total oil content reaches 30,000 ppm. Residence times stretch into hours, short-circuiting defeats the theoretical retention, and the effluent oil figure drifts with every change in feed.
Brator's Tank-within-Tank system answers this by changing the driving force rather than enlarging the tank. A three-phase hydrocyclone is built into the vessel, so separation happens in a high-intensity centrifugal field instead of a gravitational one. What follows is how that mechanism actually works, and what it delivers on a real stream.
Rise velocity of an oil droplet is governed by the density difference between the phases, the droplet diameter, and the viscosity of the continuous phase. At high oil loading the droplet population is dense and collision-prone: droplets coalesce and re-split continuously, and a thick oil layer near the surface is easily re-entrained by inlet turbulence or by the draw-off itself. Doubling the tank volume buys only a modest improvement in the theoretical retention time, while the practical short-circuiting fraction stays much the same.
A centrifugal field removes the geometric constraint entirely. Centrifugal acceleration of hundreds to a thousand times gravity shortens the distance a droplet must travel before it reaches its collection zone, so a separation that needs hours of settling completes in seconds.
Oily wastewater is fed directly into the inlet of the Tank-within-Tank system by a lift pump. Passing through a tapered pipe section, the stream is accelerated and then enters the three-phase hydrocyclone housed in the central tank. The taper does the conversion work: static pressure becomes velocity, and the tangential component establishes the swirling flow that the rest of the separation depends on.
As the stream rotates at high speed, the three phases stratify by density. The lightest fraction — oil and light-phase substances — is driven toward the central zone. The water phase, of intermediate density, moves toward the periphery. The densest solid particles migrate outward and downward, settling into the sludge space at the bottom of the vessel.
Each phase leaves through its own path. Oil is directed through the oil outlet into a designated oil-storage space, and from there it is drained continuously into an oil-storage tank while the unit stays in service. Clarified water passes through a collection and distribution piping system into the clean-water zone and is discharged to downstream treatment units. Sludge accumulates in the sludge space and is removed periodically through a dedicated piping system.
Figure 1. Schematic cross-section of the Tank-within-Tank vessel: feed acceleration through the tapered inlet, three-phase stratification inside the hydrocyclone, and separate oil, water and sludge outlets (illustrative diagram, not to scale).
A hydrocyclone is only as good as its internal flow field. Small changes in inlet geometry, cone angle, or vortex finder depth shift the cut size and the split ratio noticeably, and a design that works on one water quality can lose efficiency on another.
The high-efficiency operation of this system is the result of long-term investment in fluid separation technology rather than a single mechanical idea. Brator holds dozens of invention and utility model patents covering the Tank-within-Tank design, and through collaboration with universities uses Computational Fluid Dynamics to analyse and continuously optimise the internal flow field of the hydrocyclone. That work is what keeps oil-removal efficiency consistent across a wide range of influent water quality conditions, instead of peaking at one nominal feed.
Practical applications demonstrate the result directly. Following treatment through the Tank-within-Tank system, total oil content falls from 30,000 ppm to below 150 ppm.
Parameter | Observed result |
Influent total oil content | up to 30,000 ppm |
Effluent total oil content | below 150 ppm |
Separation driving force | centrifugal field, 100s–1,000s × gravity |
Oil phase | continuously collected and discharged |
Sludge phase | periodically removed, reduced in volume |
Internal moving parts | none |
Table 1. Typical separation performance of the Tank-within-Tank three-phase hydrocyclone.
The operational difference is not only the effluent number. Because oil is collected and discharged continuously while the unit keeps running, recovered oil retains its residual value and can be returned to process or sold. Sludge, by contrast, is collected periodically and removed, and the volume of oily sludge generated drops significantly compared with a gravity tank where oil and solids accumulate together and are desludged as one wet mixture.
Fewer cubic metres of oily sludge means fewer hazardous-waste movements, lower disposal cost, and less manual intervention on the vessel itself.
Clarified water that meets discharge standards substantially eases the load on downstream water treatment units. In practice that shows up as steadier operation of the biological stage, longer runs between media changes on polishing filters, and fewer excursions when the upstream process swings. For a refinery or chemical plant, that predictability is worth as much as the headline removal efficiency.
Where the stream also carries emulsified oil that a centrifugal field cannot break, the usual arrangement is this unit as the primary stage followed by a micro-bubble cyclone oil separator as the polishing stage, so the two mechanisms cover the full droplet spectrum.
Moving oil-water separation from a gravitational field to a centrifugal one is a small change in principle and a large one in outcome: seconds instead of hours, 30,000 ppm down to below 150 ppm, oil recovered instead of disposed of, and sludge volume reduced at the same time. The Tank-within-Tank three-phase separation system delivers resource recovery and stringent discharge compliance in the same vessel, which is what makes it a dependable technical solution for refining and chemical oily wastewater rather than a marginal upgrade. To model the mechanism against your own feed analysis, contact Brator's process engineers with your oil content, solids loading, and target effluent.
Inquiry Now
From Brator, to the World