Oil Removal Solutions for Industrial Oily Wastewater

Coking Plant Ammonia Liquor: Physical Oil Removal

Banner

How to Remove Oil from Excess Ammonia Liquor in Coking Plants? A Purely Physical Coking Wastewater Treatment Approach

November 16th, 2026

Coking plants rarely fail on wastewater volume. They fail on one particular stream. Residual ammonia liquor—the liquor left behind after the primary cooling of raw coke-oven gas and the spraying carried out in gas-collecting mains—arrives carrying almost everything the rest of the plant works hard to keep out of its water: heavy tar, free oil, fine suspended solids, high turbidity, and a viscosity that slows every downstream step the design assumed would run fast.

Most plants answer with chemistry. Coagulants and flocculants are dosed, the liquor is settled, and the clarified overflow is sent onward. The method works well enough to keep a plant running, and that is precisely the problem: it keeps running while costs, sludge volumes, and compliance risk accumulate quietly in the background. Qingdao Brator Environmental Protection Technology Co., Ltd. has taken a different route—a coupled physical process that removes the oil and the solids without adding a single chemical to the water.

Why Residual Ammonia Liquor Defeats Conventional Treatment

A Stream That Is Both Dirty and Unstable

The composition of residual ammonia liquor is genuinely difficult. It is typically dark grey-brown, noticeably viscous, and carries dense concentrations of free oil together with suspended solids. Heavy tar does not simply float; it adheres, thickens, and drags fine particles with it, which is why turbidity and oil content tend to move together rather than independently. Influent quality also shifts with oven operation, so a process that is tuned for one week of production is often mis-tuned for the next.

The Four Costs of a Chemical Route

Chemical coagulation and sedimentation carry four distinct penalties. The first is direct cost: coagulants and flocculants are consumables, and consumption scales with load. The second is sludge—large quantities of oily hazardous sludge that must be dewatered, transported, and disposed of, which turns a treatment step into an ongoing waste-management contract. The third is the chemistry itself: added agents can introduce new pollutants into the water and interfere with downstream reuse and biochemical systems. The fourth is operational fragility—oil and suspended solids removal tends to be inconsistent, and the process has poor tolerance for influent fluctuations. Open-system operation adds a fifth: volatile organic compounds escape from exposed liquor surfaces and become an air-side compliance issue as well.

For a coking enterprise pursuing green development, the actual requirement is narrow and demanding: efficient oil removal, rapid turbidity reduction, and stable water reuse, with no chemical additives, minimal sludge, and zero secondary pollution.

Table 1. Chemical coagulation versus the purely physical coupled process

Aspect

Chemical coagulation and sedimentation

Physical coupled process

Chemical input

Coagulants and flocculants dosed continuously

No chemical additives

Sludge

Large volumes of oily hazardous sludge

Minimal sludge; drastically lower disposal load

Secondary pollution

Agents can introduce new pollutants

No new pollutants introduced

Reuse compatibility

Can interfere with reuse and biochemical treatment

Does not interfere with water recycling systems

Load tolerance

Inconsistent removal; poor shock resistance

Robust against influent fluctuations

Air-side emissions

Open systems prone to VOC release

Fully enclosed operation, zero VOC emissions

A Coupled Process Built on Physics, Not Chemistry

The process was not assembled from catalogue equipment. Brator worked with the Dalian Institute of Chemical Physics (CAS), the Ningbo Institute of Materials Technology and Engineering (CAS), and the China University of Petroleum, then validated the concept on-site using actual residual ammonia liquor samples. Several pretreatment routes were evaluated before the company settled on a dedicated purification pathway for this stream: micro-bubble pretreatment followed by coalescence-based oil removal, both operating purely physically.

Stage One: Micro-Bubble Pretreatment for Suspended Solids

Compared with coagulation-based clarification, micro-bubble technology delivers a much higher mass-transfer efficiency and removes suspended solids decisively. It needs no chemical additives and generates only minimal sludge, so the two largest cost lines of a conventional plant—chemicals and sludge disposal—largely disappear. Just as importantly, it delivers a stable, well-clarified intermediate stream, which is the foundation the oil-removal stage depends on.

Stage Two: Coalescence for Advanced Oil Removal

Clarified liquor from the first stage enters a coalescence system, where the principle of physical coalescence is used to separate free and emulsified oil quickly. Small droplets are brought into contact, merge into larger ones, and rise; the result is high-efficiency, stable oil removal that addresses the specific behaviour of this stream—free oil that clings to walls, oil that resists settling, and water that stays turbid long after it should have cleared.

 

Figure 1. The coupled physical pathway for residual ammonia liquor: micro-bubble pretreatment for suspended solids, coalescence for free and emulsified oil, and reuse-grade or compliant discharge water.

What the Coupling Delivers

Because neither stage introduces a reagent, the process adds no new pollutants to the water and does not disturb the plant's recycling circuits. Oil that is separated can be recovered rather than disposed of together with sludge, which moves the operation from treatment toward true resource recovery. Zero secondary pollution is not a marketing phrase here; it is the direct consequence of not adding anything that would later have to be removed again.

Operating Performance in Real Coking Conditions

The system runs fully enclosed, so volatile organic compounds are contained rather than vented—zero VOC emissions at the operating boundary. It works at full liquid capacity with a short retention time and high throughput, which matters when plot space inside an existing coking plant is effectively unobtainable. Automation is high and maintenance is simple, and the process tolerates load swings well, an essential property for a stream whose quality moves with oven operation rather than with the treatment plant's preferences.

Side-Stream Treatment: Lower Investment, Faster Retrofit

For plants with large-scale water recycling needs, the recommended deployment is side-stream treatment rather than full-flow treatment. A slipstream is withdrawn, treated, and returned, which lowers initial investment and makes retrofit and construction far more convenient inside a running plant. Because the side-stream continuously removes pollutants instead of letting them accumulate, effluent quality stays consistently within discharge limits instead of drifting toward the edge of them. The treated water matches the quality required for recycling and can be reused locally, turning wastewater into an internal resource.

Research-Backed, Patent-Held, Field-Proven

Brator is a high-tech enterprise specialising in oil removal from industrial wastewater, with deep experience across petrochemicals, coal chemicals, power generation, and steel. The company's work on new materials, technologies, and processes has filled gaps in physical oil removal both domestically and internationally, and the portfolio is protected by numerous invention patents. The commercial logic follows from that: purification and resource recovery delivered in the same step, rather than traded against each other.

Conclusion: A Physical Standard for Coking Wastewater

Residual ammonia liquor will not become easier to treat. Ovens will keep producing it, tar will keep travelling with it, and discharge expectations will keep tightening. What can change is the process applied to it—from a chemical route that trades water quality for sludge and reagent cost, to a coupled physical route that removes solids and oil without adding anything to the water. Lower operating cost, minimal sludge, zero VOC emissions, and water that can actually be reused are not separate benefits; they are the same benefit seen from different positions in the plant. Coking enterprises looking for a replicable benchmark for green upgrading can review Brator's industrial oil-removal engineering capabilities and assess the process against their own liquor characteristics.


Inquiry Now

Industrial Water, Partner Win-Win

From Brator, to the World

+86 185 6151 0226

Qrcode

+86 185 6151 0226

tara@brator-ows.com